Which Is The Best Cooling For 2080Ti

The EK-Vector Strix RTX 2080 Ti RGB water block is specially designed for the ROG Strix version of NVIDIA® GeForce® RTX 2080 Ti graphics cards.

The water block covers the entire PCB length, and directly cools the GPU, VRAM and the VRM. The redesigned cooling engine has a larger footprint compared to the previous generation for better cooling performance

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used with reversed flow. 

The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. Sealing is ensured by high-quality EPDM O-rings.

The block is equipped with 4 12V RGB LED strips which are compatible with the motherboard 4-pin 12V RGB LED header. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers.

Both the NVIDIA® and ROG NVLink™ are compatible with this water block. 

ENCLOSED:

• EK-Vector Strix series high-performance water block
• Mounting mechanism with screw-in brass standoffs
• Necessary mounting screws, nuts, and washers
• 2x Nickel plated brass plug G1/4”
• 6mm Allen key
• Thermal pads
• Thermal grease EK-TIM Ectotherm (1g)

PLEASE NOTE:

ROG Strix RTX 2080Ti factory backplate is not compatible with this water block
Fittings are just for showcase and are not included
Should not be installed with any aluminum EKWB Fluid Gaming parts

Model: 3831109814123

The EK-Vector Aorus RTX 2080 Ti RGB high-performance water block is compatible with all Gigabyte Aorus® GeForce RTX 2080 Ti graphics cards.

The water block directly cools the GPU, VRAM and the VRM. These newly developed water blocks feature a redesigned cooling engine that has a larger footprint compared to the previous generation. This results in a larger surface area for heat transfer which increases the thermal performance.

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. So it can be used with weaker water pumps, or pumps running on low-speeds and still achieve top performance. The jet plate and fin structure geometry have been optimized to provide even flow in reversed water flow scenarios.

The base of the block is CNC machined out of nickel-plated copper while the top is CNC machined out of acrylic. Sealing is ensured by EPDM O-rings.

It features four integrated LED sources, two located in the terminal cover and one LED strip on each end of the water block. These are compatible with the motherboard 4-pin 12V RGB LED header. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers.

Both the NVIDIA® and Gigabyte NVLink™ are compatible with this water block.

Enclosed:

– EK-Vector Aorus series high-performance water block
– Mounting mechanism with screw-in brass standoffs
– Necessary mounting screws, nuts, and washers
– 2x Nickel plated brass plug G1/4”
– 6mm Allen key
– Thermal pads and grease EK-TIM Ectotherm (1g)

PLEASE NOTE:

• Gigabyte Aorus® RTX 2080 Ti factory backplate is not compatible with this water block!
• This product should NOT be installed with any aluminum Fluid Gaming parts!

Model: 3831109814710

The EK-Vector FTW3 RTX 2080 Ti RGB high-performance water block is specially designed for EVGA FTW version of NVIDIA® GeForce® RTX 2080 Ti graphics cards. The water block features a unique aesthetic cover over the block Terminal which is designed to showcase the graphics card model via LEDs, visible from the side.

The water block directly cools the GPU, VRAM and the VRM, and uses an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with pumps running at slower speeds. The jet plate and fin structure has been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed flow.

The base of the block is CNC machined out of nickel-plated copper while the top is CNC machined out of acrylic. Sealing is ensured by EPDM O-rings.

It features four integrated LED sources, two located in the terminal cover and one LED strip on each end of the water block which is compatible with the motherboard 4-pin 12V RGB LED header. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers.

G1/4″” threaded fittings can be used on both sides of the terminal and for multiple GPU connectivity, please refer to our offer of Scalar GPU Terminals.

Both the NVIDIA® and EVGA NVLink™ are compatible with this water block.

Enclosed:

– EK-Vector FTW3 series high-performance water block
– Necessary mounting hardware
– 2x Nickel plated brass plug G1/4”
– 6mm Allen key
– Thermal pads
– Thermal grease

PLEASE NOTE:
EVGA FTW3® RTX 2080Ti factory backplate is not compatible with this water block. This product should NOT be installed with any aluminum Fluid Gaming parts!

Model: 3831109816783

The EVGA GeForce RTX 20-Series Graphics Cards are powered by the all-new NVIDIA Turing architecture to give you incredible new levels of gaming realism, speed, power efficiency, and immersion. With the EVGA GeForce RTX 20-Series gaming cards you get the best gaming experience with next generation graphics performance, ice cold cooling, and advanced overclocking features with the all new EVGA Precision X1 software. The new NVIDIA GeForce RTX GPUs have reinvented graphics and set a new bar for performance. Powered by the new NVIDIA Turing GPU architecture and the revolutionary NVIDIA RTX platform, the new graphics cards bring together real-time ray tracing, artificial intelligence, and programmable shading. This is not only a whole new way to experience games – this is the ultimate PC gaming experience.

The EK-FC RTX 2080 +Ti Classic RGB – Nickel + Plexi is a high-performance full-cover water block from the EK® Classic Product Line for NVIDIA® GeForce RTX 2080 and RTX 2080 Ti graphics cards.

This water block comes with pre-installed 4-pin 12V RGB LED strip.

This water block directly cools the GPU, RAM, and VRM as water flows directly over these critical areas thus allowing the graphics card and it’s VRM to remain stable under high overclocks.

It features a central inlet split-flow cooling engine design for best possible cooling performance, which also works flawlessly with reversed water flow without adversely affecting the cooling performance. This kind of efficient cooling will allow your high-end graphics card to reach higher boost clocks, thus providing more performance during gaming or other GPU intense tasks. 

The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of high-quality acrylic material. The sealing is ensured by quality rubber O-rings. Screw-in brass standoffs are pre-installed and allow for safe, painless installation procedure.

This product is compatible with popular RGB sync technologies from all major motherboard manufacturers. The arrow marking on the 4-pin LED connector is to be aligned with the +12V marking on the RGB header.

G1/4″ threaded fittings can be used on both sides of the FC terminal and for multiple GPU connectivity, please refer to our offer of GPU Terminals.

PLEASE NOTE:

TO PREVENT DAMAGE TO YOUR WATER BLOCK, YOUR COOLANT MUST CONTAIN ANTICORROSIVES AND BIOCIDES! EK RECOMMENDS USE OF EK CRYOFUEL COOLANTS.
NVIDIA® NV links are compatible with this water block. 3rd party NV Link support is not guaranteed.
This product should NOT be installed with any aluminum Fluid Gaming parts!

Model: 3831109813737

The EK-Vector Trio RTX 2080 Ti RGB – Nickel + Plexi high-performance water block is specially designed for MSI Gaming X Trio version of NVIDIA® GeForce® RTX 2080 Ti graphics cards. 

The water block directly cools the GPU, VRAM and the VRM. These newly developed water blocks feature a redesigned cooling engine that has a larger footprint compared to the previous generation of EK® Full Cover water blocks. 

The EK® Vector Series water blocks use an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed flow.

The base of the block is CNC machined out of nickel-plated electrolytic copper while the top is CNC machined out of acrylic material. Sealing is ensured by EPDM O-rings. The block is equipped with three 12V RGB LED strips which are compatible with the motherboard 4-pin 12V RGB LED header. 

Both the NVIDIA® and ROG NVLink™ are compatible with this water block.

Enclosed:

– EK-Vector Trio series high-performance water block
– Necessary mounting hardware
– 2x Nickel plated brass plugs
– Thermal pads / grease EK-TIM Ectotherm (1g)

PLEASE NOTE:

• MSI Gaming X Trio 2080 Ti factory backplate is not compatible with this water block
• This product should NOT be installed with any aluminum Fluid Gaming parts
• TO PREVENT DAMAGE, YOUR COOLANT MUST CONTAIN ANTICORROSIVES AND BIOCIDES

Model: 3831109814581

EK-Vector Strix RTX 2080 Ti Backplate – Black is a CNC machined retention backplate made from black anodized aluminum, that fits all EK-Vector Strix RTX 2080 Ti water blocks.

Backplate covers the whole length of graphics cards PCB, serves as an aesthetic add-on and also provides passive cooling for the backside of the voltage regulation module (VRM) and the GPU core.

This backplate is guaranteed to be compatible with all ROG Strix RTX 2080 Ti graphics cards.

Enclosed:

• EK-Vector Strix RTX 2080 Ti Backplate – Black
• Mounting mechanism
• Thermal pads

Model: 3831109814970

The EK-Vector FTW3 RTX 2080 RGB high-performance water block is specially designed for EVGA FTW version of NVIDIA® GeForce® RTX 2080 graphics cards. 

The water block directly cools the GPU, VRAM and the VRM as cooling liquid is channeled directly over these critical areas. Features a redesigned cooling engine that has a larger footprint compared to the previous generation of EK® Full Cover water blocks. This results in a larger surface area for heat transfer which increases the thermal performance.

Uses an Open Split-Flow cooling engine design which proved to be a superior solution for GPU water blocks. It is characterized by low hydraulic flow restriction, which means that it can be used with weaker water pumps, or pumps running on low-speed settings. The jet plate and fin structure geometry have been optimized to provide even flow distribution with minimal losses and optimal performances even when used in reversed flow.

The base of the block is CNC machined out of nickel-plated copper while the top is CNC machined out of acrylic. Sealing is ensured by EPDM O-rings. 

The block is equipped with 4 12V RGB LED strip which is compatible with the motherboard 4-pin 12V RGB LED header. This product is compatible with popular RGB sync technologies from all major motherboard manufacturers.

G1/4″” threaded fittings can be used on both sides of the terminal.

Both the NVIDIA® and EVGANVLink™ are compatible with this water block.

Enclosed:

– EK-Vector FTW3 series water block
– Mounting mechanism with screw-in brass standoffs
– Necessary mounting hardware
– 2x Nickel plated brass plug G1/4”
– 6mm Allen key
– Thermal pads/grease

PLEASE NOTE:

– EVGA FTW3® RTX 2080 factory backplate is not compatible with this water block!
– This product should NOT be installed with any aluminum Fluid Gaming parts!

Model: 3831109818749

EK-Vector FTW3 RTX 2080 Ti Backplate – Nickel is a CNC machined retention backplate made from nickel plated aluminum, that fits all EK-Vector FTW3 RTX 2080 Ti water blocks.

Backplate covers the whole length of graphics cards PCB, serves as an aesthetic add-on and also provides passive cooling for the backside of the voltage regulation module (VRM) and the GPU core.

This backplate is guaranteed to be compatible with all EVGA FTW3® RTX 2080 Ti graphics cards.

Enclosed:
– EK-Vector FTW3 RTX 2080 Ti Backplate – Nickel
– Mounting mechanism
– Thermal pads

Made in Slovenia – Europe!

Model: 3831109816844

The EK-FC RTX 2080 +Ti Backplate Classic – Black is a CNC machined retention backplate made from black anodized aluminum for EK-FC RTX 2080 +Ti Classic RGB – Nickel + Plexi water blocks.

Backplate covers the whole length of graphics cards PCB, serves as an aesthetic add-on and also provides passive cooling for the backside of the voltage regulation module (VRM).

This backplate is guaranteed to be compatible only with reference design GeForce RTX 2080 and RTX 2080 TI graphics cards.

Enclosed:
– EK-FC2080 RTX (Ti) Classic Backplate – Black

Developed in Europe.

PLEASE NOTE:

The backplate does not serve as a standalone unit and is compatible with EK-FC RTX 2080 +Ti Classic RGB – Nickel + Plexi water block! Backplate screws can be found in the special compartment inside the box.

Model: 3831109813768

Conclusion

By our suggestions above, we hope that you can found cooling for 2080ti for you.Please don’t forget to share your experience by comment in this post. Thank you!